fbpx
Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

Buttweld Fittings in Piping (ASME B16.9)

What are buttweld fittings in piping? Buttweld fittings are pipe fittings used to change the pathway of a pipeline (elbows), reduce/increase the pipe bore size (reducers), branch (tees, cross) or blind a pipeline (butt weld cap). ASME B16.9 (and MSS-SP 43) Buttweld fittings are used for piping systems above 2 inches in diameter, whereas socket weld and threaded fittings are used for smaller size pipes (ASME B16.11).

BUTTWELD FITTINGS IN PIPING

Buttweld fittings are available in multiple shapes (elbows, tees, reducers, crosses, caps, stub ends), material grades (carbon, high-yield carbon, low-alloy, stainless, duplex, and nickel alloys), and dimensions (2 to 24 inches in seamless execution, and welded for larger pipe sizes).

The key specifications for buttweld fittings are the ASME B16.9 (carbon and alloy fittings) and the MSS SP 43 (that integrates ASME B16.9 for stainless steel, duplex, and nickel alloy BW fittings).

Butt welding fittings have the following benefits

  • allow strong, and leak-proof, piping connections
  • minimize pressure drops and the turbulence inside the pipeline
  • have a long service life
  • are rather cheap to purchase and deploy
Types of pipe fittings: elbow, tee, reducer, cap, cross

For piping systems below 2 inches in diameter, socket weld and threaded (forged) fittings are generally used (ASME B16.11).

BUTTWELD ELBOW 45/90/180 DEG.

ASME B16.9 buttweld elbows are manufactured in a wide range of dimensions (combinations of outside diameter and wall thickness) to fit ASME B36.10 and ASME B36.19 carbon, alloy and stainless steel pipes of any size between 2 and 48 inches (and above).

Buttweld elbows below 24 inches in diameter are produced by cutting, heating and bending seamless steel pipes; pipe elbows of larger sizes are manufactured, instead, from welded pipes or steel plates. 

The three most common types of elbows in piping are the 45, 90, and 180 degrees (or return elbow), as shown in the image:

Types of elbows in piping
Some special types of pipe elbows are:

  • reducing elbow: a pipe connector with an inlet and an outlet in two different bore sizes is used instead of the combination of a standard elbow and concentric reducer.
  • mitered elbow: large size elbow assembled by joining steel plates

reducing elbow

SHORT VS LONG RADIUS ELBOW

The center to face distance of a long radius pipe elbow is always 1.5 times the nominal pipe size, whereas, for a short radius pipe elbow, the center to face distance is equal to the nominal pipe size.

Example:

  • For a 4 inches long radius (LR) butt weld elbow, the center to face distance is 4 x 25.4 x 1.5 = 152.4 mm;
  • For a short radius butt weld elbow, the center to face distance is instead 4 x 25.4 x 1 = 101.6 mm. Short radius pipe elbows are available only for the 90 and 180-degree configuration (and not for the 45 degrees); instead, long radius elbows are available for all degrees.

LR elbows .       SR elbows

 

 PIPE ELBOW MANUFACTURING PROCESS

Buttweld elbows 45 and 90 degrees can be manufactured in different ways, the main ones are the “mandrel process” and the “cold forming” (other methods are the elliptical forming and the double-seam welding method).

Mandrel Process

Pipe Elbow Manufcturing Process (Mandrel Process)

Cold forming

Elbow manufacturing process (Cold forming method)

Source: TK Bend

BUTTWELD TEE

EQUAL TEE

An equal tee, otherwise called straight tee, is a buttweld fitting used to branch a pipeline, or any other pipework, at 90 degrees.

 

Equal tee asme b36.19

A pipe tee is defined “equal” when the bore size at the run and branch sides have the same diameter. An equal tee is, therefore, used to connect two pipes of the same nominal diameter.

Equal tees are available in sizes from half an inch to 48 inches (or larger) and in seamless and welded execution (seamless up to 24 inches, welded for tee sizes above 24 inches).

Buttweld tees are manufactured according to ASME B16.9 (carbon and alloy) and MSS SP 43 (stainless steel and nickel alloy).

REDUCING TEE

A reducing tee features a smaller bore size at the branched pipe side (generally 2/3 sizes smaller).

In case a larger bore size reduction is necessary, then a reinforced branch connection (such as a Weldolet) shall be preferred to prevent turbulence and have a smoother flow reduction.

reducing tee asme b36.19

The standard dimensions and tolerances of equal and reducing pipe tees are covered by the ASME B16.19 specification (carbon and alloy steel) and by the MSS SP 43 spec (for stainless steel and nickel alloys tees).

BARRED TEE

A barred tee is a special type of (equal) tee used for pigging operations (reducing barred tees do not exist, as the pig would not pass through the reduced area anyway).

A barred tee features a welded restriction on the branch pipe side that prevents the pig from flowing from the run pipe into the branched pipe.
Such barred restriction is welded on the internal side of the fitting and looks like a steel cage.

barred tee

PIPE TEE MANUFACTURING PROCESS

Cold forming is the most used manufacturing process for seamless buttweld tees, as illustrated below. Other methods are the single or double seam welding process.

Buttweld tee manufacturing process cold forming

Source: TK Bend

BUTTWELD CROSS

A Butt weld cross fitting is used when a double branch at 90 degrees is required, which is a rather rare need.

ASME B16.9 and MSS SP43 define the pipe cross dimensions and tolerance. There are no specific limitations in terms of available sizes and schedules for butt weld crosses.

pipe cross double branch fitting

 

BUTTWELD REDUCERS

CONCENTRIC REDUCER

The open ends of a concentric reducer are aligned and centered one to the other. Generally, this type of pipe reducer is used to modify the bore size of the pipeline by two (maximum three) measures, to avoid an excessive pressure drop in the pipeline.

If a larger reduction is needed, then a sequence of reducers shall be used to have a smooth and gradual adjustment of the pipeline bore size (vs. a drastic change).

For small bore size reductions, reducing flanges may be an alternative to buttweld reducers.

Concentric reducer

ECCENTRIC REDUCER

The open ends of an eccentric reducer are in an “offset” position one to the other.

Eccentric reducers are used, generally, for pipelines installed in a horizontal position (whereas concentric reducers are used for pipelines installed vertically or for the inlets of suction pumps, as top flat eccentric reducers).

Eccentric Reducer

TOP AND BOTTOM FLAT ECCENTRIC REDUCER

Eccentric reducers can be top flat (“TF”) or bottom flat (“BF”).
The bottom flat eccentric reducer type is used for pipe-racks (the bottom of the reducer is flat and at the same level of the bigger sized run pipe), while the top flat pipe reducer type is used at the inlet of piping suction pumps as shown in the image below (this setup prevents the formation of vapor traps in the pipeline):
Top flat and bottom flat eccentric reducer for suction pump

CONCENTRIC VS ECCENTRIC REDUCER

The key difference between concentric vs eccentric reducer is the centricity of the inlet vs. the outlet of the fitting, which is perfect for a concentric reducer and offset of an eccentric reducer.

BW REDUCER MANUFACTURING PROCESS

Cold forming is the most common manufacturing process for seamless eccentric/concentric reducers (welded reducers are produced with the single or double seam weld process):

Buttweld reducer manufacturing process

PIPE CAP

A buttweld pipe cap is used to blind or isolate the pipeline, permanently or temporarily (for example during the execution of maintenance and reparation works).

Buttweld pipe caps are manufactured using steel plates for most sizes and materials. The shape of a pipe cap is ellipsoidal and conforms to the requirements set by the «ASME Boiler and Pressure Vessel» code.

buttweld pipe cap asme b36.19

PIPE CAP MANUFACTURING PROCESS

The manufacturing process of caps starts from steel plates that are cut and shaped with a cold forming procedure:

Buttweld cap manufacturing process

Source: TK Bend

SEAMLESS VS WELDED BW FITTINGS

Butt weld fittings are available in seamless and welded execution (seamless for bore sizes below 24 inches, welded for sizes above 24 inches).

Seamless buttweld fittings have no seam welds and are therefore considered superior to welded BW fittings (a weld is always a weak point on the metal, prone to corrosion).

Seamless BW fittings are manufactured by cutting, heating and shaping seamless pipes into desired forms. Welded buttweld fittings have one, two or more welds, depending on the dimension, the type of fitting and the manufacturing process adopted by the mill.

 

buttweld fitting pipe connection

 

BUTT WELD FITTINGS MANUFACTURERS

Buy pipes, valves fittings online

LOOKING FOR BUTTWELD FITTINGS EX STOCK?

Buy carbon and stainless steel buttweld fittings on our online store: we offer stock delivery, competitive prices, and worldwide shipping.

Buy ASME buttweld fittings now!

Contact us if you require more information.

Comments

So empty here ... leave a comment!

Leave a Reply

Your email address will not be published. Required fields are marked *

Sidebar